履带式喷杆低量喷雾机结构设计毕业论文

 2021-04-07 02:04

摘 要

农林病虫草害严重危害农林业发展,农药飘移是化学喷洒的最主要问题。农药的低利用率不仅浪费了农药,还对环境造成了严重的污染。利用低量喷雾技术防治农林病虫害是现代植保施药的一项新技术,它有效地解决了传统施药过程中存在的问题。

本文设计了一款履带式喷杆低量喷雾机,它是由支撑装置、升降调节装置、喷杆、供液装置、旋翼气流辅助装置、折叠装置及履带底盘等组成。

本次主要设计的是支撑装置、升降调节装置、喷杆这些基本结构。支撑装置需能容纳各个部件,结构简单且实用;升降调节装置是靠链条、齿轮的结合实现升高和下降;喷杆与升降装置中装了合页折叠装置,可以实现对不同高度的作物进行喷洒。

设计了超低量喷雾系统,其中包括离心式喷头的设计、供液系统的设计、液泵的设计和药液箱的设计。

最后设计了一款履带底盘,从橡胶履带的选择到驱动轮、承重轮、导向轮的设计及其他参数的确定。

关键词:病虫害;喷杆;超低量;喷雾机

Structural Design of Crawler Spraying Rod Electrostatic Sprayer

窗体顶端

窗体底端

窗体顶端

窗体底端

ABSTRACT

Pests and disease of agriculture and forestry endanger agriculture and forestry development seriously. Pesticide drift is the most important problem of chemical spraying. The low utilization of pesticides is not only a waste of pesticides, but also caused serious pollution to the environment. The use of electrostatic spraying technology to control agriculture and forestry pests and diseases is a new technology of modern plant protection, it solves the problems in the traditional application process effectively.

In this paper, a low-volume sprayer is designed, which consists of supporting device, lifting and adjusting device, spray bar, liquid supply device, rotor air flow auxiliary device, folding device and tracked chassis.

窗体顶端

This 窗体顶端

窗体顶端

窗体顶端

窗体底端

窗体底端

This is the main design of the support device, lifting adjustment device, spray bar these basic structure.The support device is capable of accommodating the various components, which is simple and practical. Lifting adjustment device is by chain and gear combination to achieve the rise and fall. Spray bar and lift device installed in the hinge folding device and it can achieve the different height of the crop spray.

窗体顶端

窗体底端

Designed ultra-low spray system, including the design of the electrostatic sprayer, the design of the liquid supply system and the design of the liquid pump and the design of the liquid tank.

Finally, a tracked chassis was designed, from the choice of rubber track to the drive wheel, bearing wheel, guide wheel design and other parameters to determine.

Key words:Pests and disease ; Spray ; Sprayer ; electrostatic

目录

1 绪论 1

1.1 研究的目的及意义 1

1.2 国内外研究现状 2

1.2.1 喷杆喷雾机概述 2

1.2.2 国内外喷杆喷雾机的发展现状 2

1.2.3 喷杆喷雾技术概述 4

1.3 研究内容 8

1.4 预期目标 8

1.5 本章小结 8

2 喷杆低量喷雾机的总体设计 9

2.1 喷杆低量喷雾机的总体方案的确定 9

2.2 喷杆低量喷雾机基本结构 9

2.3 喷杆低量喷雾机的原理 10

2.4 本章小结 11

3 喷杆喷雾机主要部件设计 12

3.1 支撑装置的设计 12

3.2 升降调节装置的设计 13

3.3 喷杆结构设计 15

3.4 本章小结 16

4 喷雾系统的设计 17

4.1 超低量雾化系统的设计 17

4.1.1 超低量雾化方式 17

4.1.2 离心式喷头的设计 17

4.1.3 工作原理 18

4.2 供液系统的设计 18

4.2.1 液泵的构造及工作原理 19

4.2.2 药液箱的设计 19

4.3 本章小结 20

5 履带底盘的设计 21

5.1 橡胶履带的选择 21

5.2 驱动轮的设计 21

5.3 承重轮的设计 22

5.4 其它主要尺寸参数的确定 23

5.5 本章小结 24

结 论 25

致 谢 26

参考文献 27

附录A 29

1 绪论

1.1 研究的目的及意义

受生态环境恶化和全球气候异常的影响,农林病虫害日趋严重,我国遭受农林病虫草害的面积也在不断地扩大。防治病虫害的方法有很多,其中化学农药防治是使用最广、见效最快的方法[1],但化学农药既是控制植物病、虫、草害的主要手段,又是污染的主要因素之一。采用常规的方法喷施农药(见图1-1),农药的利用率很低。我国农药的有效利用率只有30%左右,发达国家为60%~70%,而真正到达害虫体的药量不到施药量的1%[9]。换言之,农药的低利用率不仅浪费了农药,还变成了环境污染源。造成这种问题的主要原因之一是我国施药技术和植保机械的落后。提高植保机械化水平,是保证农业高产、环保和可持续发展的基础。随着现代高效农业的发展,植保机械在不停地更新换代。精确施药技术能控制雾滴的飘移,提高药液在作物上的沉积率。在常规喷雾条件下,过大的湿润展布能力导致药液大量流失,过小则会使药液接触角过大,容易从叶面滚落,这两种情况都会降低药液的使用效率[2]。解决这一问题的主要办法是喷杆喷雾机技术。

图1-1 手工施药

您需要先支付 80元 才能查看全部内容!立即支付

课题毕业论文、开题报告、任务书、外文翻译、程序设计、图纸设计等资料可联系客服协助查找,优先添加企业微信。